N5JLD dot NET

What I do in my Spare Time

User Tools

Site Tools


ham:equipment:accessories

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

ham:equipment:accessories [11/17/2026 19:11] – created Jonham:equipment:accessories [11/17/2026 19:11] (current) – Jon
Line 280: Line 280:
   * **Bonding Rule:** Never install an isolated ground rod for the radio shack without bonding it to the main electrical utility ground; unbonded rods create dangerous ground-potential differences during nearby lightning strikes.   * **Bonding Rule:** Never install an isolated ground rod for the radio shack without bonding it to the main electrical utility ground; unbonded rods create dangerous ground-potential differences during nearby lightning strikes.
  
- 
-OUTSIDE (Antenna Side)                   ENTRY WALL / WINDOW                  INSIDE (Shack Side) 
-──────────────────────                 ─────────────────────                ───────────────────── 
-[HF/6m Antenna] ──► Coax ──► [1:1 Choke] ──┐ 
-├──► [Gas-Tube Arrestor] ══╗ 
-[2m/70cm Ant.]  ──► LMR-400 ───────────────┘    (DC-Blocked / PolyPhaser) 
-║  Heavy Copper Plate 
-[Rotator/Control] ─► Shielded Cable ──────────► [Surge Protector]   ══╬═ (Mounted at Entry) 
-║ 
-║  #6 AWG Solid Copper 
-▼ 
-[8-ft Ground Rod] 
-│ 
-│  #6 AWG Bond Wire 
-▼ 
-[Main House AC Service Ground] 
-INSIDE SHACK GROUNDING (Single-Point Bus): 
-[Entry Panel Inside Side] ══► [1:1 Line Isolator / Choke] ──► [Tuner / Amp / Radio] 
-│                                                           │ 
-└─────────────── Short Copper Strap / Braid ────────────────┘ 
-(Bonds all chassis together) 
 ===== 7. Grounding, Surge Protection & RFI Prevention Checklist ===== ===== 7. Grounding, Surge Protection & RFI Prevention Checklist =====
-• Arrestor Selection: Choose gas-discharge tube (GDT) or DC-blocked bulkheads (e.g., PolyPhaser, Alpha Delta, Morgan) rated for your frequency range and maximum amplifier PEP wattage. Use a DC-pass arrestor only on lines feeding a mast-mounted LNA or remote tuner via bias-tee. + 
-• Common-Mode Chokes: Install 1:1 ferrite chokes at antenna feedpoints and on the shack side of the entry panel to keep RF off feedline shields and out of USB cables. +  *Arrestor Selection: Choose gas-discharge tube (GDT) or DC-blocked bulkheads (e.g., PolyPhaser, Alpha Delta, Morgan) rated for your frequency range and maximum amplifier PEP wattage. Use a DC-pass arrestor only on lines feeding a mast-mounted LNA or remote tuner via bias-tee. 
-• USB & Control Cable Ferrites: Wind 3–5 turns of USB, CAT, and PTT cables through Type-31 or Type-43 ferrite toroids/snap-on cores near the computer and radio. +  *Common-Mode Chokes: Install 1:1 ferrite chokes at antenna feedpoints and on the shack side of the entry panel to keep RF off feedline shields and out of USB cables. 
-• Single-Point Ground & Bonding: Bond the transceiver, power supplies, tuners, amplifiers, and entry panel to a single copper ground bus using short, wide tinned-copper strap. Never install an isolated ground rod without bonding it to the main electrical utility ground.+  *USB & Control Cable Ferrites: Wind 3–5 turns of USB, CAT, and PTT cables through Type-31 or Type-43 ferrite toroids/snap-on cores near the computer and radio. 
 +  *Single-Point Ground & Bonding: Bond the transceiver, power supplies, tuners, amplifiers, and entry panel to a single copper ground bus using short, wide tinned-copper strap. Never install an isolated ground rod without bonding it to the main electrical utility ground.
  
ham/equipment/accessories.txt · Last modified: by Jon