← Back to Active Fleet Overview
This page stores the verified firmware configuration, port mappings, PID/filter tuning parameters, and recovery backups for UAS-01 (Apex-5).
diff all backup from a different firmware version (e.g., Betaflight 4.4 into 4.5) or different flight controller target without reviewing every line. Motor resource remapping and DShot settings must be verified with propellers removed on the bench.
| Parameter | Current Value | Notes |
|---|
| Aircraft Callsign | UAS-01 (Apex-5) | 5“ True-X Freestyle / Chase |
| Firmware & Version | Betaflight 4.5.1 (STM32F7X2) | Release Build (2026-08-14) |
| FC Board Target | SPEEDYBEEF7V3 (Example Target) | Soft-mounted on M3 silicone gummies |
| ESC Firmware | BLHeli_32 / AM32 v2.16 | Bidirectional DShot600 • 48kHz PWM |
| Receiver Protocol | ExpressLRS 2.4GHz (CRSF) | 500Hz Packet Rate • Model Match ID: 01 |
| Last Verified Backup | 2026-11-18 | Flight-tested and Blackbox verified |
Documenting physical UART assignments prevents guesswork when rebuilding or updating firmware.
| UART Port | Connected Peripheral | Configurator Setting | Notes |
|---|
| USB VCP | PC Configurator / Blackbox | MSP (115200) | Do not disable. |
| UART 1 | DJI O4 / O3 Air Unit | MSP + DisplayPort | OSD Canvas: HD (50×18). |
| UART 2 | ExpressLRS 2.4GHz RX | Serial RX | Inverted: OFF • Half-Duplex: OFF. |
| UART 3 | Unused / Spare | — | Reserved for GPS rescue module. |
| UART 6 | ESC Telemetry | ESC Sensor | Current meter calibrated (Scale: 185). |
How to update: Connect to Betaflight Configurator → CLI Tab → type diff all → click Save to File or copy-paste below.
# version # Betaflight / STM32F7X2 (S7X2) 4.5.1 # start the command batch batch start # reset configuration to default settings defaults nosave board_name SPEEDYBEEF7V3 manufacturer_id SPBE # feature feature -AIRMODE feature OSD feature ESC_SENSOR # serial serial 0 131073 115200 57600 0 115200 serial 1 64 115200 57600 0 115200 serial 5 1024 115200 57600 0 115200 # aux aux 0 0 0 1700 2100 0 0 # ARM (AUX1) aux 1 1 1 1300 1700 0 0 # ANGLE MODE (AUX2 Mid) aux 2 28 2 1700 2100 0 0 # BEEPER (AUX3 High) aux 3 35 3 1700 2100 0 0 # FLIP OVER AFTER CRASH (AUX4 High) # master set gyro_lpf1_static_hz = 0 set gyro_lpf2_static_hz = 650 set dyn_notch_count = 1 set dyn_notch_q = 500 set dyn_notch_min_hz = 100 set dyn_notch_max_hz = 650 set dshot_bidir = ON set motor_pwm_protocol = DSHOT600 set motor_poles = 14 set dshot_idle_value = 550 set failsafe_procedure = DROP set vbat_min_cell_voltage = 330 set vbat_warning_cell_voltage = 350 set pid_process_denom = 2 profile 0 # profile 0 (6S 1300mAh Freestyle Tune) set dterm_lpf1_dyn_min_hz = 95 set dterm_lpf1_dyn_max_hz = 190 set dterm_lpf2_static_hz = 190 set p_pitch = 52 set i_pitch = 92 set d_pitch = 44 set f_pitch = 135 set p_roll = 49 set i_roll = 88 set d_roll = 41 set f_roll = 130 set p_yaw = 45 set i_yaw = 90 set f_yaw = 110 set d_min_roll = 36 set d_min_pitch = 39 set feedforward_averaging = 2_POINT set feedforward_smooth_factor = 45 set feedforward_jitter_factor = 7 rateprofile 0 # rateprofile 0 (Actual Rates - 720 deg/s Max) set rates_type = ACTUAL set roll_rc_rate = 14 set pitch_rc_rate = 14 set yaw_rc_rate = 14 set roll_expo = 54 set pitch_expo = 54 set yaw_expo = 50 set roll_srate = 72 set pitch_srate = 72 set yaw_srate = 68 # end the command batch batch end save
Complete every step below before installing propellers after restoring or modifying a CLI backup:
save and rebooted without red ERR lines.3.50V warning threshold) and home arrow/RSSI dBm readouts are visible.| Date | Firmware | Author / Pilot | Summary of Changes |
|---|
| 2026-11-18 | Betaflight 4.5.1 | Pilot-01 | Increased D-term filter slider from 1.0 to 1.25 after Blackbox noise check; motors cool. |
| 2026-10-04 | Betaflight 4.5.1 | Pilot-01 | Switched rates from Betaflight to Actual (720 deg/s max) and enabled Model Match ID 01. |
| 2026-08-19 | Betaflight 4.5.1 | Pilot-01 | Initial build commissioning, Bidirectional DShot600 setup, and current sensor calibration. |