An op-amp has two inputs—the Non-Inverting input ($V_+$) and the Inverting input ($V_-$)—and one Output ($V_{OUT}$). When configured with Negative Feedback (connecting $V_{OUT}$ back to $V_-$ through a resistor or network), an ideal op-amp obeys two fundamental rules:
Use the reference matrix below to build standard analog signal-conditioning stages:
| Circuit Topology | Input Terminal Used | Closed-Loop Gain ($A_v$) / Output Formula | Input Impedance ($Z_{in}$) | Primary Applications |
|---|
| Voltage Follower (Unity-Gain Buffer) | $V_+$ (Output tied directly to $V_-$) | $V_{OUT} = V_{IN}$ ($A_v = 1$) | Extremely High ($> 10 | 9\ \Omega$) | Isolating high-impedance sensors (pH probes, piezo, voltage dividers) from heavy ADC loads |
|---|---|---|---|---|---|
| Non-Inverting Amplifier | $V_+$ (Feedback divider $R_f, R_g$ on $V_-$) | $V_{OUT} = V_{IN} \left(1 + \frac{R_f}{R_g}\right)$ | Extremely High | Amplifying weak positive sensor signals without loading the source; preserves signal phase | |
| Inverting Amplifier | $V_-$ through $R_{in}$ ($V_+$ tied to `GND` or $V_{ref}$) | $V_{OUT} = -V_{IN} \left(\frac{R_f}{R_{in}}\right)$ | Equal to $R_{in}$ | Precision scaling, attenuating signals ($R_f < R_{in}$), virtual-ground summing | |
| Inverting Summing Amplifier | Multiple inputs ($V_1, V_2 \dots$) through $R_1, R_2 \dots$ into $V_-$ | $V_{OUT} = -R_f \left(\frac{V_1}{R_1} + \frac{V_2}{R_2} + \dots\right)$ | $R_1, R_2 \dots$ per channel | Audio/signal mixing, adding DC offset bias to AC signals, simple R-2R DACs | |
| Differential Amplifier | Both $V_+$ and $V_-$ via matched resistor pairs ($R_1, R_2$) | $V_{OUT} = \frac{R_2}{R_1}(V_2 - V_1)$ | Moderate ($R_1$ / $R_1 + R_2$) | High-side shunt current sensing, Wheatstone bridge amplification, rejecting common-mode noise | |
| Integrator (Active Low-Pass) | $V_-$ through $R_{in}$; capacitor $C_f$ in feedback loop | $V_{OUT} = -\frac{1}{R_{in}C_f} \int V_{IN}\,dt$ | Equal to $R_{in}$ | Triangle/ramp wave generation, analog PID controllers, charge integration | |
| Differentiator (Active High-Pass) | $V_-$ through $C_{in}$; resistor $R_f$ in feedback loop | $V_{OUT} = -R_f C_{in} \frac{dV_{IN}}{dt}$ | Capacitive | Edge detection, rate-of-change sensing (requires small series input resistor to prevent oscillation) |
Selecting the wrong op-amp for a low-voltage or single-supply circuit is a common source of clipping and offset errors. Always check these five parameters:
Op-amps do not have a dedicated “Ground” pin—they only see the total voltage difference between their $+V$ and $-V$ power pins:
When powering an op-amp from a single positive supply and `GND`, negative output voltages are impossible (`0 V` is the floor):
| Part Number | Supply Range | Architecture / Specialty | Rail-to-Rail? | Typical Applications |
|---|
| `LM358` / `LM324` | `3 V – 32 V` (Single/Dual) | General-purpose bipolar (Dual / Quad) | Input includes `GND` (not $+V$); Output swings to `GND` | Low-cost DC sensor amplification, battery monitors, basic voltage followers |
| `TL072` / `TL082` | `7 V – 36 V` ($\pm 3.5\text{ V}$ to $\pm 18\text{ V}$) | JFET-input, low noise, high slew rate (`13 V/µs`) | No (needs ≥ `1.5 V – 2 V` headroom from rails) | Audio preamps, active filters, high-impedance instrumentation |
| `MCP6002` / `MCP6004` | `1.8 V – 6.0 V` (Single) | Low-power CMOS (`1 MHz` GBWP) | Yes (Full RRIO) | `3.3 V` / `5.0 V` Arduino/STM32/ESP32 sensor conditioning & ADC buffers |
| `OPA2134` / `NE5532` | `5 V – 36 V` ($\pm 2.5\text{ V}$ to $\pm 18\text{ V}$) | Ultra-low distortion (`0.00008%` THD), high-current drive | No | Hi-Fi audio, precision active crossovers, studio line drivers |
| `INA219` / `INA180` | `2.7 V – 5.5 V` (Senses up to `26 V+`) | Dedicated Current-Sense Amplifier (matched internal resistors) | Yes | High-side battery current monitoring in drones, robotics, and power supplies |
| `LM393` / `LM339` | `2 V – 36 V` (Single/Dual) | Dedicated Voltage Comparator (Open-Collector output) | Input includes `GND` | Zero-crossing detectors, window comparators, over-voltage trip circuits (requires output pull-up resistor) |
Electronics Reference: 1. Diodes & Transistors | 2. Integrated Circuits (ICs) | 3. Communication Buses (UART, SPI & I2C) | 4. Voltage Regulators & Power Supply Design | 5. Operational Amplifiers (Op-Amps)